The Cellar  

Go Back   The Cellar > Main > Creative Expression

Creative Expression Post your own works and chat about them

Reply
 
Thread Tools Display Modes
Old 07-19-2013, 09:24 PM   #1
BigV
Goon Squad Leader
 
Join Date: Nov 2004
Location: Seattle
Posts: 27,063
DIY Cedar Shingle Roof

Well, the weather was nice recently and my nephew E asked me to help him with an assignment: replace the roof on the shed at his house. I can bring my tools? We get to work with cedar? An outdoor project, in nice weather, with good company? Game on!

Here's E standing at the starting rung, ready to tear the roof off the sucka! Which we did, with our fingertips for the most part, occasionally resorting to small prybars for some nails.
Name:  IMG_3210sm.jpg
Views: 5177
Size:  88.7 KB


There was a single layer of roofing paper under the 23 year-old shingles, and it was MOSTLY intact, but that just means the accumulated water only poured through the roof in a few places.
Name:  IMG_3213sm.jpg
Views: 4236
Size:  125.9 KB


Kind of like skip sheathing, there wasn't a solid sheet of material for the roof. We cleaned it up completely. This part of the shed was still in good condition, so we started moving forward here, having completed our demolition work.
Name:  IMG_3214sm.jpg
Views: 4189
Size:  105.2 KB


Most of the first layer of roofing paper is on.
Name:  IMG_3216sm.jpg
Views: 3822
Size:  85.6 KB
__________________
Be Just and Fear Not.

Last edited by BigV; 07-19-2013 at 10:04 PM.
BigV is offline   Reply With Quote
Old 07-19-2013, 09:34 PM   #2
BigV
Goon Squad Leader
 
Join Date: Nov 2004
Location: Seattle
Posts: 27,063
We put on two complete layers of roofing paper, overlapping by about half. It was cut a little long, which we trimmed later.
Name:  IMG_3220sm.jpg
Views: 3933
Size:  90.7 KB


This is just a test fitting to determine what it looks like to have the first course doubled, and a five inch exposure.
Name:  IMG_3224sm.jpg
Views: 3840
Size:  159.1 KB


Fast forward a few courses later, we're running through the end of the bundle of shingles. I developed a strategy of lining up the new course of shingles across the entire width of the roof and paid attention to where the edges (not the ends side to side) lined up. I made sure no two courses had any shingles that had edges that lined up. Once I knew which shingles would be placed in which order, I then used a five inch wide shingle to determine how much of the undershingle to leave exposed, nailed down the first shingle, then slid the measuring board along, squaring up shingles along the way, nailing them down as I went.
Name:  IMG_3230sm.jpg
Views: 3968
Size:  63.0 KB


Looks nice, doesn't it? By the way, it smells divine. Almost done here.
Name:  IMG_3233sm.jpg
Views: 3888
Size:  174.5 KB
__________________
Be Just and Fear Not.

Last edited by BigV; 07-19-2013 at 09:42 PM.
BigV is offline   Reply With Quote
Old 07-19-2013, 09:47 PM   #3
xoxoxoBruce
The future is unwritten
 
Join Date: Oct 2002
Posts: 71,105
Shingles and shakes are laid differently.
Attached Images
  
__________________
The descent of man ~ Nixon, Friedman, Reagan, Trump.
xoxoxoBruce is offline   Reply With Quote
Old 07-19-2013, 09:50 PM   #4
BigV
Goon Squad Leader
 
Join Date: Nov 2004
Location: Seattle
Posts: 27,063
We got a single board of bevel siding to replace four sections of siding that were pretty far gone. The vertical trim board missing from E's right at the edge of the front wall of the shed where he's working was replaced with new cedar on both sides of the front.
Name:  IMG_3235sm.jpg
Views: 4110
Size:  107.1 KB


Nearly done here. The last three courses of shingles were too long to fit on the roof and so we cut them down. Even the uppermost course was a little long and so we made the exposure of the next to top course four inches so we'd have more shingle to work with.
Name:  IMG_3237sm.jpg
Views: 5279
Size:  62.0 KB


Ridge boards on. You can see the shorter exposure on the upper courses. Not visible in this picture is the adjustment I made to the ridge board that was underneath. I cut a bevel along the length of the board so that when they overlap, it makes a less acute joint between the ridge boards.
Name:  IMG_3243sm.jpg
Views: 3919
Size:  69.7 KB


Victory pose!
Name:  IMG_3241sm.jpg
Views: 3812
Size:  72.0 KB
__________________
Be Just and Fear Not.
BigV is offline   Reply With Quote
Old 07-19-2013, 09:55 PM   #5
xoxoxoBruce
The future is unwritten
 
Join Date: Oct 2002
Posts: 71,105
Good job, that change in exposure on the last course, don't mean shit and it's a smart move strength wise. In 25 years when you're re-roofing, you'll remember why you did that, and do it again.
__________________
The descent of man ~ Nixon, Friedman, Reagan, Trump.
xoxoxoBruce is offline   Reply With Quote
Old 07-19-2013, 09:57 PM   #6
BigV
Goon Squad Leader
 
Join Date: Nov 2004
Location: Seattle
Posts: 27,063
Shakes vs shingles: looks like the principal difference is how the underlayment is applied. We thought we asked for shakes, but we got shingles. Also, we definitely laid the roofing paper "shingle style". As for all those metric exposure and spacing and course offsets, we were a little less precise. And we used more nails, four per.

Once the cedar has a chance to dry out thoroughly, we'll get a can of wood preservative/water repellant and paint it on the exposed wood.

eta: thanks xoB!
__________________
Be Just and Fear Not.
BigV is offline   Reply With Quote
Old 07-19-2013, 10:00 PM   #7
BigV
Goon Squad Leader
 
Join Date: Nov 2004
Location: Seattle
Posts: 27,063
I just noticed in the "victory pose" shot that you can see the bevel I put on the right hand ridge board. I did it caveman style, with the hatchet side of the shingle hammer, just slicing away rough chunks. I was careful to go with the grain and had to turn the board around near the end to keep from diving deeply into the board. It worked out.
__________________
Be Just and Fear Not.
BigV is offline   Reply With Quote
Old 07-19-2013, 10:52 PM   #8
ZenGum
Doctor Wtf
 
Join Date: Oct 2007
Location: Badelaide, Baustralia
Posts: 12,861
That looks great. We don't do shingles much down here - either tiles or corrugated iron, mostly - but I like them.


Was all that done in one day?
__________________
Shut up and hug. MoreThanPretty, Nov 5, 2008.
Just because I'm nominally polite, does not make me a pussy. Sundae Girl.
ZenGum is offline   Reply With Quote
Old 07-19-2013, 10:58 PM   #9
BigV
Goon Squad Leader
 
Join Date: Nov 2004
Location: Seattle
Posts: 27,063
Thanks.

It could have been done in one day, had E calculated the quantity of shingles required correctly. As it was, we discovered that we were one bundle short, thirty minutes after the lumber yard closed, but with another four hours of daylight remaining. It was a leisurely day and a half, including three trips to the lumberyard, and a couple trips to the hardware store and back to my house for tools.
__________________
Be Just and Fear Not.
BigV is offline   Reply With Quote
Old 07-19-2013, 11:53 PM   #10
ZenGum
Doctor Wtf
 
Join Date: Oct 2007
Location: Badelaide, Baustralia
Posts: 12,861
Yeeeap, that's about normal. A bit more of this, or, we need one of those, or this bit doesn't fit with that bit. Back to the store.


Quote:
Originally Posted by BigV View Post
We thought we asked for shakes, but we got shingles.
Cheap handjobs are never a good idea.
__________________
Shut up and hug. MoreThanPretty, Nov 5, 2008.
Just because I'm nominally polite, does not make me a pussy. Sundae Girl.
ZenGum is offline   Reply With Quote
Old 07-20-2013, 12:10 AM   #11
Lamplighter
Person who doesn't update the user title
 
Join Date: Jun 2010
Location: Bottom lands of the Missoula floods
Posts: 6,402
My God, V. You really set yourself up for Z this time
Lamplighter is offline   Reply With Quote
Old 07-20-2013, 12:49 AM   #12
BigV
Goon Squad Leader
 
Join Date: Nov 2004
Location: Seattle
Posts: 27,063
sometimes, it's like that shit just writes itself.
__________________
Be Just and Fear Not.
BigV is offline   Reply With Quote
Old 07-20-2013, 08:19 AM   #13
Lamplighter
Person who doesn't update the user title
 
Join Date: Jun 2010
Location: Bottom lands of the Missoula floods
Posts: 6,402
I know what you mean...
Lamplighter is offline   Reply With Quote
Old 07-20-2013, 08:33 AM   #14
Griff
still says videotape
 
Join Date: Feb 2001
Posts: 26,813
Did you buy any new hammers? Great job!
__________________
If you would only recognize that life is hard, things would be so much easier for you.
- Louis D. Brandeis
Griff is offline   Reply With Quote
Old 07-20-2013, 02:22 PM   #15
zippyt
LONG LIVE KING ZIPPY! per Feetz
 
Join Date: Mar 2003
Location: Arkansas
Posts: 7,661
Good job uncle V !!!

And I, ll leave the hand job jokes to some body else !
__________________
"Success is getting what you want. Happiness is wanting what you get. "
Brother Dave Gardner
zippyt is offline   Reply With Quote
Reply

Tags
diy


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 01:50 AM.


Powered by: vBulletin Version 3.8.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.